Posts Tagged ‘cpu’

AMD New Six Core CPU

Does AMD Know their Market anymore?

Read more...

Amd Clock and Windows &

I think amd needs to update it's clock tool, or windows seven is doing weird stuff.

Read more...

I upgraded pc for gtaiv

I yanked out the old single core  mother board and processor

with Amd754 64bit 3400 mb cpu

and the nvidia 7600 gs 512 mb ram

and two gig pc 3200 ddr  ram

this computer was maxed out, the processor size was the max, the ram was the two gig max and the video card, well they don’t put out much for an agp  slot, for less than about 300 bucks, and still make it worth having.

to install

Athlon  5600+ dual 64bit am2 (2900mghz)

2 gigs pc 6400 ddr2 corsair mem

EVGA nvidia 9500 gt with 512 ddr2

Crazy thing is, the memory will not max out till it gets seated with 16 gigs.  Untill they sell  8 gig mem cards for cheap, and microslop allows you to install that much ( I believe 64 vista allows a large number , unsure what that is.) I will be fine with two gigs.

I of course had an issue installing xp. I kept seeing a lock up while trying to install Vista. So I tried the un-thinkable. I installed Xp 64 bit. Crazy, it fired right up and installed everything smoothly. I whent to all manufacture’s websites and bam…. the drivers  ready and available.

I decided to go onthe regular benchmarking I do.

I started with gtaiii . The game that always lags when ou go through the underpasses, when branches pass over the car, or china town where the banners flap as you pass through. not one hitch,hiccup,fsb burp.

Windows xp 64, the operating system that was such a problem to everyone, now is the best I have ever seen. I can not believe what is going on,.

Next I jumped on vice city, walked out of the safe house jumped in a banshee and headed with teh shoreline to my right. I made it to the malibu club and about a block later… wait … wtf.. what did I see?.. I turned around.. right in front of the parking lot behind the club is a sign. !!! a sign!!! I get out of the banshee to read the sign and it says “no standing, no parking,m2″ a bunch of other stuff and something that looked like the back of a bus.

Why have I never seen this before?… Well while I was standing there.  people started walking up .. and they just stood there. Like they where waiting for a bus..  ok.. so the new card, ddr2  and the 64 bit combo just turned something on I have never seen before..   WHAT ?

So I drive around and test my typical lag areas. all was smooth.

I am about to jump into vice city and see what goes on there.

I like my machine now.

My son’s computer specs

We are building him a computer right now.

Well he is , I am just telling him how to do it easier. He spent his Christmas and birthday money  on this build.

We had to go to fry’s and to wal~mart . Wal~mart for the monitor because he had like $200 in Wal~mart gift cards.

He got dual 2.2 x2 Pentium processor , two gigs of of kingston pc2-5300 memory , nvidia 8500 gt pci-e with 512 memory.

He is right now in the middle of snapping the motherbaord in and cussing up a storm .. lol  that’s my midget!!!!

Should go good with the tower I bought him for Christmas  with the 500wt power supply and 3 ( I think it was 3) case fans. with the dvd/cdrw combo .

Right now the only thing on this machine that is old, is the 80 Maxtor hard drive.

Not bad for a 14 year old kid, but guess who his daddy is? :-P

Precautions For Building Computers

Use lots of overhead light. Once you have all the parts together, find a flat, smooth, clean, static-free surface. Make sure your clothes are not polyester or you stand a chance of building up buttloads of static and having a merciless discharge turning your junk into… well… junk.

I like using Gatorade lids to hold my screws and small parts in. Yeah Trailer Park Boys-ish, I know, but it works. Working above tile is good, also, so you can hear the small parts when they drop and kinda locate them easier by where the sound comes from. With the tower open and all parts scattered on the table, lower the motherboard in. Take small pin nails and set them through the mounting holes to mark your spot — should take like 6-9 of them depending on board size and tower abilities. Pull motherboard back out and try to not disturb the pin nails. Replace each nail with mounting studs, lower board in, and screw it down. Follow instructions in the manuals for motherboard and instructions from tower to set up power switches and USB connectors. you may sometimes need to split the end connector for the tower speaker so it fits the prongs. Tie back wires so they stay low and out of view.

Insert RAM, CPU, and heat sink. Simply put: Be gentle, be slow, bend no prongs, and scratch no boards

Set in all drives: CD-ROM / DVD / hard drive / floppy drive. Place the power supply in, and take the board connecting the wire strand and try and map the cleanest, least visible route. Then plug it in. Do not crack the motherboard (yes, it can happen)! Do the same with the drives. I tie them to the rack as I go down the line. Keep hard drives away from all magnets — even the case speaker magnet!

The Video card is done pretty much the same way as the RAM. The slit(s) in the card tells you which way it should face.

Get a good look at the inner case. All air paths need to be clear of anything — even wires. Now plan the path your air will flow and then look at your fans to see which direction the blades should face to achieve the airflow you planned.

Close the case, cross toes, plug in all devices for first boot, and press power button. Pray for BIOS/CMOS boot. Press delete and watch temperatures for about ten minutes or until you see that it is getting really hot.

More stuff to keep in mind.

Computer Hardware Installation

Installing hardware into a fresh PC is not that complicated, really.

If the prongs and the holes line up, read the part number and look it up and check compatibilities. Sometimes some hardware is too powerful, so checking specs is always a plus. 80% of the time they will work, but sometimes you can run into problems — like an AMD Athlon XP will not fit into an AMD Athlon 64 board. Same goes for AMD and Pentium. Prongs won’t line up.

The red wire always faces toward the power source. Look really close to the IDE cables (even the ones with the center top hole filled); you will notice there is a red dotted wire. Magnify it if you need to. Same with the FDD seven cable twist. FDD plugs in after the twist — never before.

PCI or AGP video cards just clip in. If it has a hook at the end, it is AGP. If not, then it is not. AGP will be the smaller slot.

Memory is just a clip in, also. Look up board manufacturers and part numbers and read through the specs for the board to know the minimum and maximum memory capabilities for your PC. (I have also looked this up more than… well, plenty of times and can easily do it. You can, too!)

With the CPU, once again, part numbers and manufacturer numbers are of wonderful help. Check board specs, check CPU specs, and always double check before the hard part, which is sliding the CPU into the dock. Squirt a thin layer of heat sink paste on the side facing away from the motherboard. Set the heatsink onto the CPU and center it before it actually touches (so you don’t smear off the heat paste while wiggling all around to position it). Clasp the retainer on either side. Screw the fan down to the heatsink. Plug the fan into the board.

With the power supply, make sure you have one strong enough to run your fan and that meets your CPU’s requirements. Make sure it is fastened really tightly; clip all wires into what ever hole they fit in (this is usually true). If you have one drive power connector that has no other splices or additional connectors on it, I would suggest you either use it for the master drive or you could plug your fans and lights into that connector.

With IDE and FDD cables, red goes toward the power source.

The use of a hot glue gun by splatting a tad at the clasps for most parts except the CPU is okay to prevent stuff from falling out of place.

Scroll to the bottom of my page if you want to make a donation and request further assistance. Any donation helps! If the problem is resolved, please pass this link on when you know of someone in need.